a
V-40iT 5-axis machining centre
travel
X-axis: 838mm (33”)
Y-axis: 635mm (25”)
Z-axis: 488mm (19.2”)
X/Y/Z-axis feed motor: 4kW (5.4 hp)
distance from table to spindle nose: from 48.26 to 533mm (from 1.9” to 21”)
distance from column front to spindle centre: 635mm (25”)
axis guide ways: linear roller for high speed + high accuracy + high torque machining
table
table diameter: 350mm (13.8”)
table fixture plate: 400 x 500m (15.75” x 19.68”)
maximum load capacity: 200kg (440 lbs.) from 0° to 45° / 100kg (220 lbs.) from 60° to 90°
tilting angle range: from +40° to -120°
t-slot width: 12mm (0.47”)
height from floor to table top: 1219mm (48”)
brake torque: 35kg/cm2
spindle
spindle nose: CAT#40
spindle bearing inner diameter: 70mm (2.75”)
spindle power S1-100% (S6-40%): 15kW (20.1 hp)
spindle torque: 51.7 ft-lbs
maximum speed: 12,000 rpm
transmission: H.T.D. belt
tool clamping force: 848kg (1870 lbs.)
feed rate
X/Y-axis rapid feed rate: 36m per minute (1417” per minute)
Z-axis rapid feed rate: 20m per minute (792” per minute)
X/Y/Z-axis maximum cutting feed rate: 10m per minute (394” per minute)
A/C-axis rapid feed rate: 25 rpm
automatic tool changer
type: arm
tool shank: CAT#40
number of tool pockets: 30
maximum tool diameter with adjacent tool: 80mm (3.15”)
maximum tool diameter with adjacent empty pockets: 109mm (4.3”)
maximum tool length: 250mm (9.8”)
maximum tool weight: 7kg (15.4 lbs.)
tool-to-tool change time: 1.8 seconds
accuracy
positioning accuracy / repeatability: ±0.01mm / 0.007mm (±0.00039” / 0.00028”)
general
machine length x width x height: 3840 x 2200 x 2718mm (151.2” x 86.6” x 107”)
machine weight : 7000kg (15,432 lbs.)
electrical requirements: 400 volt / 3-phase
standard + included equipment
Fagor 8065 POWER 5-axis simultaneous control
linear + rotary scales for high accuracy
belt type chip conveyor with built-in auger type chip conveyor
work light
alarm light
heat exchanger
rigid tapping
remote manual pulse generator (MPG = electronic hand wheel)
through tool air blast
surrounding coolant system (coolant ring)
300 psi coolant through the spindle
wash down system
spindle oil cooler
spindle air purge
Renishaw TS-27 tool measuring probe
X-axis: 838mm (33”)
Y-axis: 635mm (25”)
Z-axis: 488mm (19.2”)
X/Y/Z-axis feed motor: 4kW (5.4 hp)
distance from table to spindle nose: from 48.26 to 533mm (from 1.9” to 21”)
distance from column front to spindle centre: 635mm (25”)
axis guide ways: linear roller for high speed + high accuracy + high torque machining
table
table diameter: 350mm (13.8”)
table fixture plate: 400 x 500m (15.75” x 19.68”)
maximum load capacity: 200kg (440 lbs.) from 0° to 45° / 100kg (220 lbs.) from 60° to 90°
tilting angle range: from +40° to -120°
t-slot width: 12mm (0.47”)
height from floor to table top: 1219mm (48”)
brake torque: 35kg/cm2
spindle
spindle nose: CAT#40
spindle bearing inner diameter: 70mm (2.75”)
spindle power S1-100% (S6-40%): 15kW (20.1 hp)
spindle torque: 51.7 ft-lbs
maximum speed: 12,000 rpm
transmission: H.T.D. belt
tool clamping force: 848kg (1870 lbs.)
feed rate
X/Y-axis rapid feed rate: 36m per minute (1417” per minute)
Z-axis rapid feed rate: 20m per minute (792” per minute)
X/Y/Z-axis maximum cutting feed rate: 10m per minute (394” per minute)
A/C-axis rapid feed rate: 25 rpm
automatic tool changer
type: arm
tool shank: CAT#40
number of tool pockets: 30
maximum tool diameter with adjacent tool: 80mm (3.15”)
maximum tool diameter with adjacent empty pockets: 109mm (4.3”)
maximum tool length: 250mm (9.8”)
maximum tool weight: 7kg (15.4 lbs.)
tool-to-tool change time: 1.8 seconds
accuracy
positioning accuracy / repeatability: ±0.01mm / 0.007mm (±0.00039” / 0.00028”)
general
machine length x width x height: 3840 x 2200 x 2718mm (151.2” x 86.6” x 107”)
machine weight : 7000kg (15,432 lbs.)
electrical requirements: 400 volt / 3-phase
standard + included equipment
Fagor 8065 POWER 5-axis simultaneous control
linear + rotary scales for high accuracy
belt type chip conveyor with built-in auger type chip conveyor
work light
alarm light
heat exchanger
rigid tapping
remote manual pulse generator (MPG = electronic hand wheel)
through tool air blast
surrounding coolant system (coolant ring)
300 psi coolant through the spindle
wash down system
spindle oil cooler
spindle air purge
Renishaw TS-27 tool measuring probe
walk-around pictures of the Leadwell V-40iT 5-axis machining centre
the Leadwell V-iT 5-axis machining centre brochure
the Fagor 8065 control brochure
