MACHINE SPECIFICATIONS
spindle taper: CAT #50
boring spindle diameter: 4.41”
travel of boring spindle: 24”
travel of facing spindle: 7.22”
diameter of facing plate: 23”
index rotary table: 49” x 43.3”
index rotary table load: 6600 lbs.
longitudinal travel: 56”
cross travel: 64”
spindle to table distance: from 0" to 48”
programmable spindle speed: from 8 rpm to 1000 rpm
programmable X/Y/Z/W-axis feed rate: from 0.040” to 80” per minute
facing plate speed: from 4 rpm to 200 rpm
facing plate U-axis feed rate: from 0.012” to 60” per minute
X/Y/Z/W-axis rapid travel" 80” per minute
digital readout resolution: 0.0005”
main motor: 20 hp
machine length x width x height: 197” x 115” x 108”
machine weight: 39,600 lbs.
spindle taper: CAT #50
boring spindle diameter: 4.41”
travel of boring spindle: 24”
travel of facing spindle: 7.22”
diameter of facing plate: 23”
index rotary table: 49” x 43.3”
index rotary table load: 6600 lbs.
longitudinal travel: 56”
cross travel: 64”
spindle to table distance: from 0" to 48”
programmable spindle speed: from 8 rpm to 1000 rpm
programmable X/Y/Z/W-axis feed rate: from 0.040” to 80” per minute
facing plate speed: from 4 rpm to 200 rpm
facing plate U-axis feed rate: from 0.012” to 60” per minute
X/Y/Z/W-axis rapid travel" 80” per minute
digital readout resolution: 0.0005”
main motor: 20 hp
machine length x width x height: 197” x 115” x 108”
machine weight: 39,600 lbs.
STANDARD FEATURES AND EQUIPMENT
11” touch panel
point to point position control on X Y W axis at accuracy of ± 0.001”
Automatic Hole-Cycle Control Features
automatically calculate hole position or input hole position directly
“GO TO” position control for rapid approach to hole position
drilling cycle with programmable feed speed and rapid retract speed
peck dril cycle for deep hole drilling
floating tapping cycle with feed rate calculated from spindle speed and TPI
portable hand wheel unit with X Y Z W B – 5axis selection and spindle jogging for easy setup
4 axis digital read-out - X/Y/Z and W-axis at 0.0005” resolution
position readout provides full screen display on X/Y/Z/W and B-axis for better visibility
programmable feed rate in inch per minute
calculated feed rate at inch per revolution for cutting reference
three (3) feed functions: rapid traverse / cutting feed / hand wheel micro adjustment
programable spindle / facing plate speed and automatic shift of high / low gear
central operating console eliminates most of the operation handling on the headstock
automatic hydraulic clamping / unclamping coordinate with feed select on X/Y/Z/W/B + U-axis clutch
automatic lubrication power draw bar optional tailstock
optional point to point position control and digital read-out on the B-axis
11” touch panel
point to point position control on X Y W axis at accuracy of ± 0.001”
Automatic Hole-Cycle Control Features
automatically calculate hole position or input hole position directly
“GO TO” position control for rapid approach to hole position
drilling cycle with programmable feed speed and rapid retract speed
peck dril cycle for deep hole drilling
floating tapping cycle with feed rate calculated from spindle speed and TPI
portable hand wheel unit with X Y Z W B – 5axis selection and spindle jogging for easy setup
4 axis digital read-out - X/Y/Z and W-axis at 0.0005” resolution
position readout provides full screen display on X/Y/Z/W and B-axis for better visibility
programmable feed rate in inch per minute
calculated feed rate at inch per revolution for cutting reference
three (3) feed functions: rapid traverse / cutting feed / hand wheel micro adjustment
programable spindle / facing plate speed and automatic shift of high / low gear
central operating console eliminates most of the operation handling on the headstock
automatic hydraulic clamping / unclamping coordinate with feed select on X/Y/Z/W/B + U-axis clutch
automatic lubrication power draw bar optional tailstock
optional point to point position control and digital read-out on the B-axis
THE MAXCUT MHBM-110B CYCLOMATIC BORING MILL VERSUS A MANUAL BORING MILL
Manual boring mills must be stopped to switch gears using a clutch.
The MAXCUT has two ranges and infinitely variable speed. Give it a speed on the control and it will go to that speed controlled by the CYCLOMATIC control.
Manual Boring Mills have no cycles - everything is manual.
The MAXCUT has automatic facing cycles automatic positioning and drilling cycles controlled by the CYCLOMATIC control.
Manual Boring Mills: you rapid close then position by hand.
The MAXCUT give it a position on the control and it will go there within + or - .001” controlled by the CYCLOMATIC control.
Manual Boring Mills have manual clamping.
The MAXCUT automatically clamps the X/Y/Z and B-axis when you switch to XYZ or B as it will automatically unclamp.
Manual Boring Mills have B-axis power.
The MAXCUT has a B-axis power standard, optional B-axis positioning 360 degrees controlled by the CYCLOMATIC control.
Manual Boring Mills have a facing head with a power slide.
The MAXCUT has a facing head with a power slide with variable feed rates and optional U-axis giving you automatic spot facing cycles and two different internal or external grooving cycles controlled by the CYCLOMATIC control.
The MAXCUT CYCLOMATIC CONTROL is very easy to operate - no handles to turn - no gear shifts to move - no G-codes to learn - only pictures fill-in-the-blanks as it features the included optional Fagor 8055i CNC control:
Manual boring mills must be stopped to switch gears using a clutch.
The MAXCUT has two ranges and infinitely variable speed. Give it a speed on the control and it will go to that speed controlled by the CYCLOMATIC control.
Manual Boring Mills have no cycles - everything is manual.
The MAXCUT has automatic facing cycles automatic positioning and drilling cycles controlled by the CYCLOMATIC control.
Manual Boring Mills: you rapid close then position by hand.
The MAXCUT give it a position on the control and it will go there within + or - .001” controlled by the CYCLOMATIC control.
Manual Boring Mills have manual clamping.
The MAXCUT automatically clamps the X/Y/Z and B-axis when you switch to XYZ or B as it will automatically unclamp.
Manual Boring Mills have B-axis power.
The MAXCUT has a B-axis power standard, optional B-axis positioning 360 degrees controlled by the CYCLOMATIC control.
Manual Boring Mills have a facing head with a power slide.
The MAXCUT has a facing head with a power slide with variable feed rates and optional U-axis giving you automatic spot facing cycles and two different internal or external grooving cycles controlled by the CYCLOMATIC control.
The MAXCUT CYCLOMATIC CONTROL is very easy to operate - no handles to turn - no gear shifts to move - no G-codes to learn - only pictures fill-in-the-blanks as it features the included optional Fagor 8055i CNC control:
© 2025 Masteel America Corporation / disclaimer + privacy