a
MTC25-0920M turning centre
with rotary tool turret + spindle C-axis
with rotary tool turret + spindle C-axis
capacity
swing over bed: 508mm (20”)
swing over cross slide: 230mm (9.05”)
maximum turret diameter with turret: 305mm (12”)
maximum turning length with chuck: 508mm (20”)
bar capacity: 65mm (2.56”)
travel
X-axis: 215mm (8.46”)
Z-axis: 514mm (20.25”)
C-axis: 360° in 0.001° minimum increment
spindle
spindle nose: A2-6
spindle hole diameter: 65mm (2.56”)
maximum spindle speed: 4000 rpm
spindle taper: 1/20
spindle motor: 11kW (15 hp)
hydraulic chuck diameter: 10”
maximum hydraulic pressure: 30kgf/cm2 (450 psi)
sauter high performance rotary tool turret
tool stations: 12
tool shank diameter / type: VDI 30 / quick change
turning tool shank: 20mm (0.75”) square
rotary motor: 3kW (4 hp)
maximum rotary speed: 4000 rpm
axes
X/Z axis rapid feed rate: 30m per minute (1181” per minute)
X/Z axis servo motor: 11/6Nm (8.56 ft-lbs)
accuracy
positioning accuracy: ±0.01mm (±0.0004”)
repeatability: 0.005mm (0.0002”)
tailstock
tailstock quill diameter: 65mm (2.56”)
tailstock travel: 425mm (16.73”)
quill taper: MT#4
quill travel: 50mm (1.97”)
general
one piece meehanite cast steel slant bed angle: 30°
length without chip conveyor x width x height: 2388 x 1956 x 1702mm (94” x 77” x 67”)
length with chip conveyor x width x height: 3302 x 1956 x 1702mm (130” x 77” x 67”)
weight: 3200kg (7055 lbs.)
electric power requirements: 400V / 3 phase / 20 kVa
standard + included equipment
Fagor 8055 control
10” hydraulic 3-jaw chuck with soft jaws
manual tailstock with programmable quill
Renishaw manual tool setter
belt type lift-up chip conveyor
automatic part catcher
auto lubrication system
work light
M30 program stop light
tool set & box, level pads, operation manual & parts list
heat exchanger for electrical cabinet
swing over bed: 508mm (20”)
swing over cross slide: 230mm (9.05”)
maximum turret diameter with turret: 305mm (12”)
maximum turning length with chuck: 508mm (20”)
bar capacity: 65mm (2.56”)
travel
X-axis: 215mm (8.46”)
Z-axis: 514mm (20.25”)
C-axis: 360° in 0.001° minimum increment
spindle
spindle nose: A2-6
spindle hole diameter: 65mm (2.56”)
maximum spindle speed: 4000 rpm
spindle taper: 1/20
spindle motor: 11kW (15 hp)
hydraulic chuck diameter: 10”
maximum hydraulic pressure: 30kgf/cm2 (450 psi)
sauter high performance rotary tool turret
tool stations: 12
tool shank diameter / type: VDI 30 / quick change
turning tool shank: 20mm (0.75”) square
rotary motor: 3kW (4 hp)
maximum rotary speed: 4000 rpm
axes
X/Z axis rapid feed rate: 30m per minute (1181” per minute)
X/Z axis servo motor: 11/6Nm (8.56 ft-lbs)
accuracy
positioning accuracy: ±0.01mm (±0.0004”)
repeatability: 0.005mm (0.0002”)
tailstock
tailstock quill diameter: 65mm (2.56”)
tailstock travel: 425mm (16.73”)
quill taper: MT#4
quill travel: 50mm (1.97”)
general
one piece meehanite cast steel slant bed angle: 30°
length without chip conveyor x width x height: 2388 x 1956 x 1702mm (94” x 77” x 67”)
length with chip conveyor x width x height: 3302 x 1956 x 1702mm (130” x 77” x 67”)
weight: 3200kg (7055 lbs.)
electric power requirements: 400V / 3 phase / 20 kVa
standard + included equipment
Fagor 8055 control
10” hydraulic 3-jaw chuck with soft jaws
manual tailstock with programmable quill
Renishaw manual tool setter
belt type lift-up chip conveyor
automatic part catcher
auto lubrication system
work light
M30 program stop light
tool set & box, level pads, operation manual & parts list
heat exchanger for electrical cabinet
walk-around pictures of the Maxcut MTC25-0920M turning centre with rotary tool turret
the Fagor 8055 control brochure
© 2025 Masteel America Corporation / disclaimer + privacy