a
MTC25-1420 turning centre
capacity
swing over bed: 508mm (20”)
swing over cross slide: 407mm (16”)
maximum turning diameter with turret: 407mm (16”)
maximum turning length with chuck: 535mm (21”)
bar capacity: 65mm (2.56”)
travel
X-axis: 215mm (8.46”)
Z-axis: 514mm (20.25”)
spindle
spindle nose: A2-6
spindle hole diameter: 65mm (2.56”)
maximum spindle speed: 4000 rpm
spindle taper: 1/20
spindle motor: 11kW (15 hp)
hydraulic chuck diameter: 8”
maximum hydraulic pressure: 30kgf/cm2 (450 psi)
tool turret
turret type: LS-200 hydraulic
tool stations: 12
turning tool shank: 25mm (1”) square
boring bar diameter: 32mm (1.26”) diameter
rapid traverse
X/Z axis rapid feed rate: 30m per minute (1181” per minute)
accuracy
positioning accuracy: ±0.01mm (±0.0004”)
repeatability: 0.005mm (0.0002”)
tailstock
tailstock quill diameter: 65mm (2.56”)
tailstock travel: 425mm (16.73”)
quill taper: MT#4
quill travel: 50mm (1.97”)
general
one piece meehanite cast steel slant bed angle: 30°
length without chip conveyor x width x height: 2388 x 1956 x 1702mm (94” x 77” x 67”)
length with chip conveyor x width x height: 3302 x 1956 x 1702mm (130” x 77” x 67”)
machine weight: 3070kg (6,768 lbs.)
standard + included equipment
Fagor 8060 control:
or
Fanuc 0i-TF Plus control
8” hydraulic 3-jaw chuck with one set of soft and hard jaws
steel belt lift-up side exit chip conveyor
Renishaw tool setter
automatic parts catcher
heat exchanger
full enclosed splash/chip guard
foot switch for chuck open/close
spare V-belt
alarm light
five (5) clamping blocks for turning tools
five (5) clamping gibs for turning tools
two (2) facing tool holders with clamping blocks
five (5) boring bar holders
a set of boring bar sleeves
coolant nozzles
tool box with adjusting tools
leveling bolts + pads
swing over bed: 508mm (20”)
swing over cross slide: 407mm (16”)
maximum turning diameter with turret: 407mm (16”)
maximum turning length with chuck: 535mm (21”)
bar capacity: 65mm (2.56”)
travel
X-axis: 215mm (8.46”)
Z-axis: 514mm (20.25”)
spindle
spindle nose: A2-6
spindle hole diameter: 65mm (2.56”)
maximum spindle speed: 4000 rpm
spindle taper: 1/20
spindle motor: 11kW (15 hp)
hydraulic chuck diameter: 8”
maximum hydraulic pressure: 30kgf/cm2 (450 psi)
tool turret
turret type: LS-200 hydraulic
tool stations: 12
turning tool shank: 25mm (1”) square
boring bar diameter: 32mm (1.26”) diameter
rapid traverse
X/Z axis rapid feed rate: 30m per minute (1181” per minute)
accuracy
positioning accuracy: ±0.01mm (±0.0004”)
repeatability: 0.005mm (0.0002”)
tailstock
tailstock quill diameter: 65mm (2.56”)
tailstock travel: 425mm (16.73”)
quill taper: MT#4
quill travel: 50mm (1.97”)
general
one piece meehanite cast steel slant bed angle: 30°
length without chip conveyor x width x height: 2388 x 1956 x 1702mm (94” x 77” x 67”)
length with chip conveyor x width x height: 3302 x 1956 x 1702mm (130” x 77” x 67”)
machine weight: 3070kg (6,768 lbs.)
standard + included equipment
Fagor 8060 control:
- HD graphics software
- interactive icon-based programming cycles
- standard G-code programming cycles
- mix standard G-code programming cycles with interactive icon-based pages programming cycles in a single program
- DXF file upload for conversational programming with profile editor
- tool life management
- telediagnostics with on-line Fagor remote support for on-line trouble shooting through machine internet connection with the Fagor office during the warranty period
- free off-line Fagor 8060 programming software on customer’s Windows based computer
or
Fanuc 0i-TF Plus control
8” hydraulic 3-jaw chuck with one set of soft and hard jaws
steel belt lift-up side exit chip conveyor
Renishaw tool setter
automatic parts catcher
heat exchanger
full enclosed splash/chip guard
foot switch for chuck open/close
spare V-belt
alarm light
five (5) clamping blocks for turning tools
five (5) clamping gibs for turning tools
two (2) facing tool holders with clamping blocks
five (5) boring bar holders
a set of boring bar sleeves
coolant nozzles
tool box with adjusting tools
leveling bolts + pads
walk-around pictures of the Maxcut MTC25-1420 turning centre with the Fagor 8060 control
the Fagor 8060 control brochure
the Fanuc 0i-Model F Plus control brochure
© 2025 Masteel America Corporation / disclaimer + privacy